News
A complete 2-inch lift kit for a Next-Gen Ford Ranger costs between $2,458 and $3,317 at Sharp 4×4, depending on the shocks and spring rating you choose. Add fitting and a wheel alignment, and a typical fitted 2-inch lift kit cost in Perth comes to roughly $3,150 to $4,650 before any extra parts, as the breakdown below shows. This guide covers every part of that figure, what makes it rise, WA’s legal limits, and how to pick the right kit.
Most people see a kit price online and assume that’s the final bill. It usually isn’t. Here’s what usually goes into a fitted price on a popular dual-cab ute.
| Item | Typical cost |
When you need it |
| 2-inch suspension kit (Next-Gen Ranger) | $2,458 to $3,317 | Always |
| Upper control arms | $998 a pair on popular utes such as the D-Max and BT-50 | Often on IFS utes lifted 2 inches or more |
| Fitting labour | About $540 to $1,075 (4 to 8 hours at the $134.30 average hourly rate) | Always |
| Wheel alignment | $150 to $250 | Always, after fitting |
| Engineering certification | Quoted per vehicle | Lifts over 50 mm in WA |
Â
Kit and control arm figures are Sharp 4×4’s current prices, checked in November 2026. Labour and alignment figures are explained in the next section. Bigger lifts on heavier vehicles cost much more: Sharp 4×4 lists a 4-inch lift kit for the Chevrolet Silverado 1500 ZR2 at $4,180 to $5,600, and a 4-inch kit with Fox shocks for the Silverado and Sierra 1500 at $8,000 to $14,540.
Installation is the part online prices leave out, and it’s where quotes differ most. A lift kit isn’t a bolt-on accessory. Struts need to be pulled apart with a spring compressor, leaf packs come out from under the tray, and every bolt is torqued back to spec.
Strut assembly should only be done by a qualified automotive mechanic, because the job needs specialised spring compressor equipment. That’s the main reason DIY rarely saves as much as people expect.
Any fitted price from a Perth workshop should cover:
Sharp 4×4 quotes every job as a supplied and fitted price for your exact vehicle, so your final figure depends on the kit and any extra parts. Drop-off at the Bibra Lake workshop starts from 7:30 am on weekdays.
Ask any workshop for a supplied and fitted figure in writing. Cheap labour quotes that leave out the alignment or control arms won’t stay cheap once the extras land.
Two utes that look identical can end up with very different bills. Here’s what moves the price most.
Shock absorber type. Sharp 4×4’s Next-Gen Ranger kits show the spread clearly: Nitro Gas from $2,458, Foam Cell from $2,668, and Foam Cell Pro from $3,146. Better shocks cost more, but they run cooler on long corrugated roads, and that’s what you’ll want on a trip up to the Pilbara.
Load rating. Kits come with springs matched to the weight you carry. On the Ranger kits, the rear leaf pack ranges from a 0 to 200 kg rating up to 600 kg plus, and the heaviest pack adds $171 to the kit price. That’s cheap compared with replacing sagging springs a year later. Pick the rating for the weight you’ll carry with a canopy, drawers, water, and a fridge on board.
Vehicle type. Prices shift from one model to the next. Sharp 4×4’s 2-inch kits for the new Triton MV start at $2,202 with Nitro Gas shocks and reach $2,910 with Foam Cell Pro, a little below the equivalent Ranger kits.
Lift height and extra parts. Once you lift an IFS ute by 2 inches or more, the factory upper control arms often limit wheel alignment. Our guide on whether you need upper control arms after a lift covers the signs to watch for, and a pair adds about $998.
Engineering. Anything over WA’s 50 mm limit brings certification and inspection costs, which we cover below.
Two inches (about 50 mm) is the most popular lift in Perth because it sits within WA’s limit without engineering. For a Next-Gen Ford Ranger, Sharp 4×4’s current prices (November 2026) are:
|
Kit |
Price range |
| Nitro Gas | $2,458 to $2,629 |
| Foam Cell | $2,668 to $2,839 |
| Foam Cell Pro | $3,146 to $3,317 |
Â
Each range links to the kit’s product page on Sharp 4×4. The lower figure uses the lightest leaf spring rating and the higher figure the heaviest.
Other utes vary, so check the exact listing for your model before you budget. If you’re torn between heights, our 2-inch vs 3-inch lift guide compares tyre fitment, geometry and legality side by side.
Our advice is to spend more on the shocks rather than the height. A Foam Cell kit at 2 inches will serve a touring ute better than a cheap kit at 3 inches.
For a ute that tours, tows or carries real weight, yes. For a ute that never leaves the suburbs, probably not.
Done well, a kit pays for itself in a few ways:
It also has costs beyond the invoice. Lifting raises the centre of gravity, which reduces stability in sharp turns, and lifted trucks lose some fuel economy, mostly because of bigger tyres. Steeper driveshaft angles add wear, and RAC WA notes that raised ride heights can wear universal joints and wheel bearings sooner.
Warranty is a common worry. The Australian Automotive Aftermarket Association states that modifying a vehicle does not automatically void a manufacturer’s warranty. The maker still has to fix manufacturing faults unless the modification caused the problem.
WA allows a suspension lift of up to 50 mm without engineering approval. RAC WA classes suspension changes that lift a vehicle by more than 50 mm as complex modifications, and quotes an engineer who describes a 50 mm increase in tyre rolling diameter as a hard limit for 4x4s.
Going higher means following the Department of Transport’s process for complex modifications:
Skipping this is expensive. RAC WA notes that the owner or driver of an illegally modified vehicle who causes a crash may be asked to repay the Insurance Commission of WA for injury claims it paid. Tell your insurer about any lift, too, since a changed vehicle can affect your cover.
Sharp 4×4’s guide to 4WD lift kits in Perth explains which heights need approval, from 2 inches up to 6.
Start with how you’ll use the ute. The height you’d like comes second.
If you plan to add a GVM upgrade later, mention it at the quoting stage. Some kits are designed to work as part of a GVM package, which saves buying springs twice.
In the end, a fair lift kit cost in Perth comes down to the right kit for your weight and roads, fitted properly and aligned, with no surprise extras. For a Next-Gen Ranger, that means roughly $3,150 to $4,650 for a fitted 2-inch lift: a kit from $2,458 to $3,317, about $540 to $1,075 in labour and a $150 to $250 alignment. Add upper control arms and the top end reaches about $5,650.
Sharp 4×4 measures every build before and after the install and quotes a supplied and fitted price for your exact vehicle, accessories and intended use. Our Perth team fits suspension from brands including BDS and Zone Offroad at the Bibra Lake workshop and checks compliance during quoting. Browse our suspension and lift kits range, or visit the Cockburn Central or Myaree showroom for a quote.
Expect roughly $3,150 to $4,650 on a Next-Gen Ranger. That’s $2,458 to $3,317 for the kit at Sharp 4×4, about $540 to $1,075 in fitting, and $150 to $250 for the alignment. Upper control arms add about $998 if your vehicle needs them.
Yes. WA allows suspension lifts of up to 50 mm without engineering approval. Anything higher is a complex modification that needs certification, an inspection, and a modification permit.
No, not automatically. Under Australian Consumer Law, the manufacturer must still fix faults unless the lift caused them, and the fitter covers the kit itself.
Always. Lifting changes the suspension angles, and if you skip the alignment, you’ll chew through tyres, and the ute won’t steer as it should.
Yes, you should. RAC WA advises updating your insurer when a vehicle is significantly modified, and an undeclared or illegal modification can leave you exposed after a crash.
Perth Showrooms In Cockburn & Myaree.
Product focused on safety, performance and quality.
Fast, Reliable Shipping Anywhere In Australia.
Relax We Warrant Everything We Sell.
Stay up to date with our latest news and deals.